Will a 22 kW generator run my whole Frisco house?

For many Frisco homes, yes. A 22 kW unit covers full HVAC, kitchen, water heater, and daily appliances in a typical home. Add a second HVAC zone or an EV charger and you may need more. A load calculation confirms it.

Can I just use a portable generator instead?

You can, but it works differently. A portable unit requires manual setup and refueling, and it powers only a few circuits. A standby generator starts on its own within seconds and runs on your gas line. If you travel, or if someone at home cannot manage a portable unit, standby is the safer choice.

Does my Frisco home need a panel upgrade for a generator?

Often not. Homes built in the last ten to fifteen years usually have a 200-amp panel already, which handles a standby generator without modification. Older homes with 100-amp service frequently do need an upgrade. We confirm this at the assessment.

What happens if my generator is undersized?

It trips. The unit carries your running load fine, then your air conditioner tries to start, the surge exceeds capacity, and the generator shuts down. You are left without power during the outage you bought the generator to survive.

How long can a standby generator run during an outage?

As long as fuel holds out. Connected to your natural gas line, a standby unit can run for days. Propane units are limited by tank size.

Electrical Panel Replacement in Starwood, Frisco

Starwood is one of Frisco’s original gated communities, near Legacy Dr and Lebanon Rd. More than 900 custom homes line its winding, tree-lined streets.

We provide electrical panel replacement in Frisco, TX, for Starwood homes going electric. Many homes here were built with gas cooking and water heating. Switching to induction or a heat pump water heater adds big loads to a panel sized decades ago. We bring 50 years of Berkeys expertise to Frisco, so you know before you buy.

Planning a kitchen or utility update? Call us before you order appliances.

electrical panel replacement starwood - Berkeys Frisco TX

Switching From Gas to Electric in Starwood?

List the appliances you plan to switch: cooktop, oven, water heater or furnace.
Check your panel for open spaces.
Call us before you order appliances, so you know what your panel can handle.

Proudly Serving DFW Since 1975!

Signs Your Panel Can’t Take New Electric Appliances

In a Starwood home built for gas, the panel may already be busy before you add anything new. Use this table to see what common signs may mean and what to do next.

What you notice	What it often points to	What to do
No open spaces in your panel	Your panel is full	Ask us about a replacement
Breakers trip when the AC, dryer and oven run together	Your panel may be near its limit	Call us to check it
Lights dim when big appliances start	A heavy load or a loose connection	Call us to check it
Your panel is original to a late-’90s or early-2000s home	It may not be sized for added electric loads	Ask us whether it needs replacing
The panel feels warm or buzzes	A loose or damaged connection	Call us right away
A burning smell or scorch marks	A serious hazard	Leave the home and call 911

Going Electric: Induction Cooktops, Heat Pump Water Heaters and Your Panel

Starwood homes went up from the late 1990s to the mid-2000s, many with gas cooking and water heating. Owners updating kitchens and utility rooms often switch to electric. Each switch adds a big load to a panel that wasn’t planned for it.

Switches that add load:

Induction cooktops and electric ovens
Heat pump water heaters
Heat pumps in place of gas furnaces

What we check first:

Open spaces for new circuits
How much power your home uses at its busiest
Your panel’s age and condition

If there’s room, new circuits may be all you need. If not, replacing the panel first may make sense. We also plan entry through Starwood’s gate ahead of work day. You can see all of our electrician services for Frisco homes in one place.

Thinking about induction or a heat pump water heater? Call us to check your panel first.

What Happens During a Panel Replacement

Here’s what to expect when we replace the panel in your Starwood home:

We check your panel and the appliances you plan to add. Then we explain what we find.
We give you a written plan and price. We time the work with your remodel or appliance delivery.
We replace the panel, add the new circuits and test them. We confirm everything works before we leave.
We handle the City of Frisco permit and inspection. We take care of it whenever your project needs one.

Serving Starwood

Guard-gated Starwood sits near Legacy Dr, Lebanon Rd and the Dallas North Tollway. Its 16 villages share a clubhouse, community lake and trails, with streets like Stillwater Trail and Star Creek Dr. Spears Elementary, part of Frisco ISD, serves the neighborhood. Grand Park, The Star, PGA Frisco and Legacy West are all close by.

Our team serves Starwood from our Frisco location on Avon Ln. Ready to get your panel set for new electric appliances? Call (214) 216-1727 to reach our Frisco team.

Business Address: 4645 Avon Ln, Suite 260, Frisco, TX 75033